Wellcraft V20 Community

Wellcraft V20 Community (https://forums.wmpdevserver1.com/community/index.php)
-   Repairs (https://forums.wmpdevserver1.com/community/forumdisplay.php?f=16)
-   -   black covering on 89 v20 console??? (https://forums.wmpdevserver1.com/community/showthread.php?t=10284)

stuarbc 09-09-2008 01:20 PM

black covering on 89 v20 console???
 
My 89 v20 dual has some type of black paperlike covering on top of parts of the console....it has began pealing up and I wanted to replace it but cannot figure out what it is or where to purchase it from.....anyone have any information or ideas.....you can see it in the picture below

http://i272.photobucket.com/albums/j...rbc/53ff_1.jpg

rb437 09-09-2008 07:32 PM

2 Attachment(s)
I recovered the top of the console when I replaced my fish finder. I used non-skid tape. Check the before and after pics below

Skools Out 09-09-2008 07:42 PM

why don't you remove it sand then roll on some top side paint with a little non-skid, then never fear it peeling again plus easy to touch up later.

reelapeelin 09-12-2008 07:43 AM

Quote:

Originally Posted by Skools Out (Post 127890)
why don't you remove it sand then roll on some top side paint with a little non-skid, then never fear it peeling again plus easy to touch up later.


That'd be a great way to go...another way would be 1/4" Starboard...remove all the existing paper and entire dash...you might wanna consider all new gauges, too...mine looked about like yours when I first drug her home back in 1999...the old sonar unit shown here has been replaced, but this approach has worked well for long time...

http://i3.photobucket.com/albums/y90...eelin/dash.jpg

...just remove the existing dash and cut out the fiberglass behind it leaving a 3/4" lip around the outter edge to fasten new w/ #8 Stainless screws...routing the edges give it a nice finished look...a piece cut and routed to fit the top of the console would look great, too...use white up there as any other color will absorb too much heat...

Good luck w/whatever approach you take and keep us posted...

stuarbc 09-12-2008 09:49 AM

Dash has already been replace....see picture below....I am very happy with it....I just need to replace to paperlike topping....I wanted to try to stay away from sanding and painting....and grip tape is a little too rough looking

http://i272.photobucket.com/albums/j...c/IMG_1750.jpg

parishht 09-12-2008 10:41 AM

Lowe's has some countertop contact paper that might work.

I did what was to be a temporary color change on my old farmhouse kitchen counter,
4 years ago and that stuff is still holding up like new.

msbhammer 09-13-2008 12:02 PM

Thats a nice Dash set up you have there STU.
Parish, hows your V doing ?, you get her wet at all this season ?

lumberslinger178 09-13-2008 05:20 PM

stu Thats a nice dash, I have the same contact paper on top of dash but mines in pretty good

shape but it looks like just regular contact paper to me..


http://i115.photobucket.com/albums/n...8/DSC06189.jpg

reelapeelin 09-15-2008 02:10 AM

Quote:

Originally Posted by stuarbc (Post 128121)
I wanted to try to stay away from sanding and painting....and grip tape is a little too rough looking

Dash looks GREAT!!...

The Starboard topper on the console would would avoid sanding and painting and give you a great surface up there...

Stillrunning 09-15-2008 09:11 AM

My CC had the same stuff and I just peeled it off and use some adhesive remover to clean it up.


All times are GMT -5. The time now is 06:24 PM.

Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.