Need Cowlings 1980 Merc.200hp
 

Lost my cowlings and the rear cowl bracket to some rough seas while fishing yesterday. Just so you know, they don’t float and boy, did they sink fast! The front hatch (the plastic type rather than the SS locking hatch) came undone, they opened like a clam. I looked back because the sound of the motor was louder than normal and at that moment, the cowl assembly’s rear bracket brakes off. In the dunk.... Immediately I shut down, told my fishing buddy "man overboard"" and dove in. They were going down fast and with very strong current going out and a 15-20 kt wind in the opposite direction, lost site of them very quickly. My friend could not start the boat and he too was moving away really fast in the opposite direction. Thank God my friend put down an anchor and it caught, but is was a very hard swim against the current back to the boat. The last few yards I was assisted with a throw cushion tied to a rope. Once inside, I took a break, tracked back with the GPS, dropped anchor and snorkeled (just a mask – no snorkel or fins) in circles (tied to a rope) around the boat for about an hour and a half. First with a 25' radius and then 50' but I could not find them. The trip back to the marina was at 7 mph because the motor would get swamped and shut down if we went any faster. After all the time we spend catching the baitfish, we ended up dumping them all. It was their lucky day...and mine too for not having drowned after diving under those conditions without even a life jacket.
Your help in finding the replacement is appreciated.

Try looking over at www.screamandfly.com Alot of those guys ditch the clamshells for the alien cowlings to save weight.

would 150 hp,84 fit? i might have the sides, but not the front piece...

Phatdaddy, all 150 - 200 hp most likely will work and by the way, I was able to save the front cover. Some have SS vents towards the front, but as long as they look like this, they will fit.
On the older model 78-81, the front latch was stainless steel, the newer were plastic.

Thanks!

http://i138.photobucket.com/albums/q...FL/c1a7_12.jpg
http://i138.photobucket.com/albums/q...rFL/c7ac_1.jpg

These were the ones I had, but then again, I think the SS vents are an after market for improved carb air.
http://i138.photobucket.com/albums/q...0154Medium.jpg

builder, I got a set off of an early 150 2 liter, coming north any time soon? I'll check with the guys next door at HMY and see if they are headed south to the home office

I have a full set available, but are in Lewes, Delaware. I'm not sure when I will be back to Delaware, wo weeks I guess. If you look in my gallary, the one's i have are identical. Just stripped a 200 Merc. down for parts, plus rebuilt the lower unit. All are for-sale.

spareparts, those will fit too. PM me and let me know how much you want for them.
Thanks,

Hammer, thanks and yours are identical. check your pm's.

builderfl, let me know, i'm heading to bahia honda last of june...

builder, what ya got for trade??

spareparts, I'm trying to get them locally and get back on the water ASAP...I checked with UPS and they want more money to ship them than what the cowlings are worth. If nothing comes up locally, we will work something out by June. Thanks!:clap:
By the way, I realized that although they all look the same, they are not. Found ones with the metal latches and they don't fit. I need the ones that have the plastic latch in the front like the ones picture against the wall.

these have the plastic latch, don't worry, they're not going anywhere. next tiem one of the brokers heads south, I'll put them in their trunk. So...what ya got to trade?

spareparts, How about this little red truck? Needs minor repairs, but has low miles and a good engine.

http://i138.photobucket.com/albums/q...9873913071.jpg

If you don't like my little red truck, I can always send some $ your way.:beer:

nah, I allready got a project truck, allthough I could use the engine out of that one for my Cherokee(eat your heart out Ferm)

I like the straight 6 myself. Aint nuthin like a stroker 6 for torque.

Going down to Homestead, FL to look at a set of cowlings. They told me over the phone that they are a little rough and in need of some repairs...and we all know what that means.:head: Let's see what they are going to come up with. Will post pictures tomorrow.