I GOT IT!!!!!
 

Finally, after 2 trips to the UPS place. Yeah, I know, I said they were going to deliver it, but they changed that themselves. Good thing I checked the UPS tracking web site. Anywho, just to prove it's here, and to satisfy Hammers never ending thirst for pic-tars...

As delivered (picked up)
http://i29.photobucket.com/albums/c2...y/100_0709.jpg

Boy, they do a nice job with the packaging
http://i29.photobucket.com/albums/c2...y/100_0710.jpg

And here she sits, proudly upon the lower
http://i29.photobucket.com/albums/c2...y/100_0711.jpg

Now I just need an alignment tool, 2 qts of earl, and a pressure test just to make sure.

I GOT IT!!!!!
 

Finally, after 2 trips to the UPS place. Yeah, I know, I said they were going to deliver it, but they changed that themselves. Good thing I checked the UPS tracking web site. Anywho, just to prove it's here, and to satisfy Hammers never ending thirst for pic-tars...

As delivered (picked up)
http://i29.photobucket.com/albums/c2...y/100_0709.jpg

Boy, they do a nice job with the packaging
http://i29.photobucket.com/albums/c2...y/100_0710.jpg

And here she sits, proudly upon the lower
http://i29.photobucket.com/albums/c2...y/100_0711.jpg

Now I just need an alignment tool, 2 qts of earl, and a pressure test just to make sure.

I GOT IT!!!!!
 

Finally, after 2 trips to the UPS place. Yeah, I know, I said they were going to deliver it, but they changed that themselves. Good thing I checked the UPS tracking web site. Anywho, just to prove it's here, and to satisfy Hammers never ending thirst for pic-tars...

As delivered (picked up)
http://i29.photobucket.com/albums/c2...y/100_0709.jpg

Boy, they do a nice job with the packaging
http://i29.photobucket.com/albums/c2...y/100_0710.jpg

And here she sits, proudly upon the lower
http://i29.photobucket.com/albums/c2...y/100_0711.jpg

Now I just need an alignment tool, 2 qts of earl, and a pressure test just to make sure.

Re: I GOT IT!!!!!
 

So, are you done yet ;D

Re: I GOT IT!!!!!
 

So, are you done yet ;D

Re: I GOT IT!!!!!
 

So, are you done yet ;D

Re: I GOT IT!!!!!
 

Nope! See last line in above post ;)

Re: I GOT IT!!!!!
 

still got your old input shaft from the old upper? knock the u-joints out, take the o-rings off and use it as an alignment shaft, it should slide in easy, two fingers easy

Re: I GOT IT!!!!!
 

Yep still have it. I have heard others say not to do that, but I can't see why not. Either it goes in easy or it don't. I may just go ahead and do that. Gracias. ;)

Re: I GOT IT!!!!!
 

Great job. You will be in the water soon enough.
Great pics. Too. ;D ;D ;)

Re: I GOT IT!!!!!
 

Outdrive inna BOX!!...what'll they think of next ;D ... that's cooler than a burger-in-a-BAG!! 8) ...

Re: I GOT IT!!!!!
 

a proper line up shaft should be a tighter fit, but back when OMC was making the cobra, the line up shaft they used was a whole lot smaller than the merc( used the same spline size and diameter), you could line up an engine with an OMC shaft, and the merc shaft wasn't even close to fitting. If you use teh old shaft, you may have to weld a handle on it so you'll have something to grab when you pull it out

Re: I GOT IT!!!!!
 

Yep that will male a great alinement tool!

Re: I GOT IT!!!!!
 

Well, I deinstalled the old yoke and it worked perfectly for an alignment tool. Slid right in, with zero force, 1 finger pressure. I see this thread is gonna get ugly with a statement like that :-X

Re: I GOT IT!!!!!
 

We want pics. Its the weekend, you should have her done by now. ;D

Re: I GOT IT!!!!!
 

make sure you use a liberal amount of spline grease(EP) when you install the new drive



hmmmm... One finger? Which one?

Re: I GOT IT!!!!!
 

The middle one, of course ;)

Re: I GOT IT!!!!!
 

Dang Hammer, I posted 3 of em. The only thing left to show is my greasy hand after extracting it from my boat's bung hole. That's just not suitable for public viewing.

I'm gonna wait until I can get her pressure tested. Maybe next weekend, I dunno, maybe the week after. Believe me, ya'll will be the first to see her wet.

Re: I GOT IT!!!!!
 

http://i3.photobucket.com/albums/y67...0off20tree.jpg

http://i3.photobucket.com/albums/y67...inger_flip.jpg

Re: I GOT IT!!!!!
 

LOL. ;D ;D ;D ;D

Re: I GOT IT!!!!!
 

Good job on the drive, get the pics when you can, Hammer is wound up a little tight right now, his bar blew up :'(
Understandable ;)

Re: I GOT IT!!!!!
 

LOL, Willy feels my pain I'm going through. ;D