Wellcraft V20 Community

Wellcraft V20 Community (https://forums.wmpdevserver1.com/community/index.php)
-   General (https://forums.wmpdevserver1.com/community/forumdisplay.php?f=10)
-   -   Anchor Size (https://forums.wmpdevserver1.com/community/showthread.php?t=3501)

Bygracealone 09-28-2006 03:04 AM

Anchor Size
 
Hey guys,

What size anchor do most of you use? I need to buy one for my V...

turbinedoctor 09-28-2006 03:09 AM

Re: Anchor Size
 
Bygrace: I use a 9lb fluke with about 6 feet of chain. It work very well, sometimes to well. Did a quick search at Boaters world, check out the link below.

http://www.boatersworld.com/product/...ing%3Bcianchor

Bygracealone 09-28-2006 03:22 AM

Re: Anchor Size
 
Hey thanks Turbine,

I noticed they only offer the option of 8lb. or 13lb. From what you said about your anchor sometimes working too well, I'm guessing the 8lb. should work fine, right?


turbinedoctor 09-28-2006 03:25 AM

Re: Anchor Size
 
Yea it should work fine.

What I was talking about is sometimes when I go to put the anchor out and am drifting a little, it gets a really good bite and is hard to pull up. Better hard to pull than not holding.

shicks007 09-28-2006 07:49 AM

Re: Anchor Size
 
I have an 8 lb for mine. It seems to work ok, but I don't anchor a whole lot.

chumbucket 09-28-2006 09:27 AM

Re: Anchor Size
 
8lb is plenty as long as you use 4'-6' of chain. I usually kept a spare 4lb on board for a stern anchor. I didn't use it a lot, but there were certain circumstances when fishing in tight to rocks where a stern anchor was required to maintain position without bouncing off the rocks. The stern anchor was also a plus when taking the family out and beaching the boat. We often put in on a nice sandy beach that had lots of current and lots of other boats. The stern anchor kept your boat from swinging into other boats. Just drop the stern anchor before hitting the beach, then motor right up onto the beach, snub the stern line, then set your bow anchor on the beach and watch your tides. ;)

TheTinMan 09-28-2006 09:27 AM

Re: Anchor Size
 
If your anchor is not holding that great, add chain. If you anchor in deeper water and don't feel like bustin your a$$ heavin it, use this. Makes anchor retrieval sooooo easy.

http://www.fishing-catalog.com/other...nchor_ball.htm

I rarely anchor. In fact the only time I have anchored my "V" (first season w/it)was in a few feet of water hanging out at the beach. But, with Blackfish season just a few days away, that should change.

reelapeelin 09-28-2006 09:36 AM

Re: Anchor Size
 
Quote:

Originally Posted by chumbucket
Just drop the stern anchor before hitting the beach, then motor right up onto the beach, snub the stern line

This works great, just be SURE of plenty of rope or that rope is tied off to something or both ... don't ask me how I know
::) ... ;D ...

macojoe 09-28-2006 09:39 AM

Re: Anchor Size
 
I just have a anchor, weight unknown??

I do have a anchor retrieval system as above but have never used it??

Last time I anchored was Memorial day waiting for a tow :-/

Stinky_Hooker 09-28-2006 10:04 AM

Re: Anchor Size
 
I have a 13# on my 18 with about 8 feet of chain. I anchor often in wrecks up to 100' deep.

Go ahead and get one size bigger, that what I do. It never hurts in bad conditions to have a little more anchor than you need. Ive never been in a situation where I said "man I wish my anchor was smaller" ;)

Airslot 09-28-2006 10:28 AM

Re: Anchor Size
 
I have an 8# on the bow with about 6' of chain. My serious fishing anchor is a 13# with 15' of chain. I usually throw that in the boat when were working around the breakers.

Airslot

turbinedoctor 09-28-2006 09:04 PM

Re: Anchor Size
 
Heres one for the stren that looks like it works well. A guy I work with has one and likes it.


Watch the video at:

http://www.anchorbuddy.com/

macojoe 09-28-2006 09:33 PM

Re: Anchor Size
 
$29.99 *I might just get this? *Great idea for the beach!! Thanks Turbinedoctor

http://www.boatersworld.com/product/386970073.htm

Skools Out 09-29-2006 12:53 AM

Re: Anchor Size
 
i carry two 15 lb in mine with 6 ft chain and 100 ft rope each. Only reason is cause i use same two anchors on all my boats so they hold up to my 25' ers.

labii 09-29-2006 03:30 PM

Re: Anchor Size
 

I use a Danforth 5H high tensile with 6' of chain. It grabs and holds very well .

http://www.danforthanchors.com/hitensile.html

phatdaddy 09-29-2006 07:52 PM

Re: Anchor Size
 
Whatever anchor i found while diving and 20 feet of 3/8 chain. I think the chain is more important than the hook. We have a lot of soft bottom down here so that might not be true everywhere. I also use the anchor ball to retrieve.

bradford 03-11-2008 08:06 PM

I run two 8lb danforth types with 4 feet of stainless chain, and 100 ft of line each.

randlemanboater 03-12-2008 06:33 AM

I have a 20 pound "navy style" for the bow and a 12 pound "navy style" I use to keep the stern off the beach.

No need for chain with these.


http://i145.photobucket.com/albums/r...101_0067-5.jpg

nipper 03-12-2008 08:03 AM

I have 2 in my boat. The first is a Danforth style (weight unknown) with about 12' of chain and 200' of rope. The second is a navy style, 12 lb. with 6' of chain and 100' of rope. I think chain is incredibly important to keep the proper scope on the anchor rode. Blue water sailers often use all chain rodes.

charlie_the_tuna 03-12-2008 11:01 AM

8 pound danforth with 6 feet of chain.
have 2 for when i beach but i want to get a sand spike.

anybody have experience with these?

randlemanboater 03-12-2008 01:04 PM

Quote:

Originally Posted by nipper (Post 115309)
I have 2 in my boat. The first is a Danforth style (weight unknown) with about 12' of chain and 200' of rope. The second is a navy style, 12 lb. with 6' of chain and 100' of rope. I think chain is incredibly important to keep the proper scope on the anchor rode. Blue water sailers often use all chain rodes.


I agree about the chain for most anchors, but I have yet to need it with that 20 pounder. But we have mostly sand around my area of coastal pleasure. And 100 ft would be the deepest I would anchor.

Stinky_Hooker 03-13-2008 08:42 AM

Chain around here isnt only for holding power, but to keep your rope from getting cut in wrecks and such.

C YENSEN 03-13-2008 09:13 AM

I use an 8 pounder with 6' of chain and plenty of line. you never know when you will need more line. I sure as hell dont want to try to anchor in a hurry and not have enough line to get to the bottom. I think mine has roughly 150' of line.:sun:

randlemanboater 03-13-2008 10:19 AM

I probably should put a short chain on mine to protect the rode, but it is hard enough already for my little girls to pull in the 20 pounder by itself.
:oh:

As for how long should your rode be, triple the depth and there you are.

If you are anchoring in 10 ft of water x 3 = 30 feet of achor rode required.

So I carry at least 300 ft.

wpearch 03-13-2008 12:11 PM

Quote:

Originally Posted by chumbucket (Post 59153)
8lb is plenty as long as you use 4'-6' of chain. I usually kept a spare 4lb on board for a stern anchor. I didn't use it a lot, but there were certain circumstances when fishing in tight to rocks where a stern anchor was required to maintain position without bouncing off the rocks. The stern anchor was also a plus when taking the family out and beaching the boat. We often put in on a nice sandy beach that had lots of current and lots of other boats. The stern anchor kept your boat from swinging into other boats. Just drop the stern anchor before hitting the beach, then motor right up onto the beach, snub the stern line, then set your bow anchor on the beach and watch your tides. ;)

What a tide LOL:sun:

C YENSEN 03-13-2008 12:32 PM

Quote:

Originally Posted by wpearch (Post 115417)
What a tide LOL:sun:

i thought the great lakes had a little tide variation:head:

bcmarinamanager 03-13-2008 02:10 PM

Quote:

Originally Posted by randlemanboater (Post 115408)
I probably should put a short chain on mine to protect the rode, but it is hard enough already for my little girls to pull in the 20 pounder by itself.
:oh:

As for how long should your rode be, triple the depth and there you are.

If you are anchoring in 10 ft of water x 3 = 30 feet of achor rode required.

So I carry at least 300 ft.

Actually, the correct scope is 7:1. It is extremely too much, but according to the USCG, the 7:1 is the correct scope. It's more or less for if you plan on anchoring overnight. That way you have less of an angle in your rode by the time it gets down to your anchor. Usually, the length of chain should be roughly half, to 1/3rd the length of your boat.

nipper 03-13-2008 02:28 PM

Thanks BC. To the depth of the water you need to add the height of where the rode will be fastened to the boat from the water. It's not much, but that 4 or 5 feet should be factored into the equation. 7:1 is proper, and probably necessary for overnight anchoring. You can generally get away with less when you are in the boat and attentive to what is going on (i.e. whether you are drifting despite having the anchor down). I am always amazed when you see folks anchored (often with other boats rafting beside) with the anchor rode going virtually straight down.

tsubaki 03-13-2008 02:57 PM

Hell, I might as throw in.
 
http://www.wellcraftv20.com/communit...cons/icon1.gif Re: Make my life easier http://www.wellcraftv20.com/communit...my+life+easier
DIFFERENT ANCHORING APPROACH: tie a weight about 5-10 feet ahead of your normal anchor. This does the same thing as adding chain to the anchor but better. The weight can be a 10lb mushroom anchor, etc. I've never seen a more reliable positioning method.
http://i175.photobucket.com/albums/w...Picture131.jpg

randlemanboater 03-13-2008 08:28 PM

:head:7 to 1......I gotta go buy more rope.

Stinky_Hooker 03-13-2008 08:49 PM

300' is what i have....anchors me in 100-150 max, but he is rights...7:1 is what they say for safety

rb437 03-13-2008 10:00 PM

1 Attachment(s)
BGA, I use 8lb w/6ft of chain and enough line for the depth (depth usually 10-15 ft or less). If your up one one the local rivers or in a nice calm cove this will be more than enough in the sand or mud we usually find in this area. I frequently use this set up and have a SeaRay 260 Sundancer rafted to me with no problems (calm conditions of course).

jasoncooperpcola 03-14-2008 10:39 PM

We used a 14 pound fluke anchor, a 13 pound grapnel anchor, and a 16 pound claw anchor. Plus we have 25 feet of chain. 19 times out of 20 we anchored on the first try. And with an anchor ball it was no sweat bringing it back to the boat.

bcmarinamanager 03-17-2008 06:56 AM

tsubaki that's a pretty sweet set up too. I've seen something like before in a book, but never knew someone actually uses it. It is definitely the strongest way to anchor. And you're right Nipper, I don't use more than 30' when anchoring at the beach in the summer, usually in about 6-10' of water. And that's very close to a very deep and fast moving inlet. (Masonboro Inlet, NC) Water speed is around 8-10 knots! I use a 12# with 8' of 1/4" chain...sets the first time everytime. The pulpit really helps the boat stay fine when at anchor, even when I'm stern to the beach with my stern anchor on the beach, and beam-to the current. She always stays put. Of course I carry 350' for those just in case situations.....you just never know.


All times are GMT -5. The time now is 07:00 AM.

Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.