Just for HAMMER, my latest project(with pics)
 

This is my 250 SEARAY CUDDY CABIN. Pulled the engine TUESDAY(just got the camera this mornin though), and cleaned and checked her WEDNESDAY. Boat appears to have sunk down on the starboard aft corner due to a bad bellows. Engine was locked and junk and most of the interior in the rear is soft as well. But hopin to get her goin again soon.

forward STBD view
http://i162.photobucket.com/albums/t...R/HPIM0030.jpg

starboard aft view
http://i162.photobucket.com/albums/t...R/HPIM0031.jpg

the inside, a bit dirty from sittin
http://i162.photobucket.com/albums/t...R/HPIM0035.jpg

the bilge with the engine out
http://i162.photobucket.com/albums/t...R/HPIM0033.jpg

the old anchor ;D
http://i162.photobucket.com/albums/t...R/HPIM0039.jpg

how not to winterize one(shot of the inside of the port manifold, manifolds were rotted and blue anti-freeze went right in the engine)
http://i162.photobucket.com/albums/t...R/HPIM0040.jpg

and the simple failure that brought her down, small tear in the shift bellows
http://i162.photobucket.com/albums/t...R/HPIM0032.jpg

There are some other pics in my photobucket as well for ya'll.

Re: Just for HAMMER, my latest project(with pics)
 

GREAT PICS! Way to go. Sounds like you know your chit. Keep us posted.

Re: Just for HAMMER, my latest project(with pics)
 

Yo THERM. Great Pictures Brother. ;D
I do like the Sea Rays myself. SKOOl has one as well. I'll be checking out your gallery too. You doing the motor work for the Sea Ray ?

Re: Just for HAMMER, my latest project(with pics)
 

get er done ;D....great project
I see nj reg on boat where ya located .......therm

Re: Just for HAMMER, my latest project(with pics)
 

I'm located in FLORIDA, the boat was previously in JERSEY(where it sank). I came about it SEPTEMBER 2006 through my buddy who hauled it back to FLORIDA. He bought it on E-bay for $3400 back in NOVENMER 2004 and the guy told him it was a running boat just needed cleaning. He showed up to pick it up on a FRIDAY evening and it wasn't ready for sea-trial like they agreed so the seller knocked off $500 and he drug it all the way back to FLORIDA. He brought it to me to get it running and I found all the bad news as soon as I popped the engine cover off. He owed me some money from a JEEP engine I did for him so he gave me the boat in trade(I know bad deal). It took me almost 2 months to get a title for it, but I finally got the title in my name. So it's time to GET'R DONE!

I'm the one doing the engine work(UNFORTUNATELY), and all of the other repairs. I prefer working on outboards, but this thing is worthless like it sits. Of the 2 engines I picked up last weekend, one of them is free so I'm going to clean it up and set it in there and replace all of the bellows and such to stop the leaks up. It was amazing how much water could come in around the shift cable through that small hole in the shift bellows. And since I've finally got a camera I'm gonna try and make myself take pics.

The one on the left is free, the one on the right is locked up solid. They're both 350 TBI motors, 260HP and about 2001 models.
http://i162.photobucket.com/albums/t...R/HPIM0042.jpg

Re: Just for HAMMER, my latest project(with pics)
 

I wise man once told me "If they're rusty on the outside, they're danm sure rusty on the inside!"


And your friend got hosed on that deal!!!!

Re: Just for HAMMER, my latest project(with pics)
 

Well they may be rusty on the outside, and somewhat inside the cooling passages.

BUT IT SOUNDS GREAT!

Cleaned up the bellhousing mounting surface and mounted up the flywheeel, bellhousing and starter. Cleaned out the fuel system, and put new injectors in it($700 from MERCRUISER :o, but only $140 from AUTOZONE ;D). And she came to life ;). I still have to replace the manifolds, risers and water pump. But it sounds great, starts instantly and revs up real nice.

And yeah, he got ELEPHANT F >:(CKED without vaseline. But now he's hoping he can buy it back after seeing how cheap I got an EFI engine that is the right HP for the ALPHA 1 outdrive.

Re: Just for HAMMER, my latest project(with pics)
 

Good for you bro! I'd probably trashed it by the way it looked.

Re: Just for HAMMER, my latest project(with pics)
 

Good Job Therm. Glad you got the other motor running.
Been trying to Get SKOOLS Sea Ray for Free, but those southern fo's in NC. never heard of the word Freebee. ;D ;D ;D ;D ;D

Re: Just for HAMMER, my latest project(with pics)
 

I seen the engine after it was pulled back in 03, it looked real nice then. The other engine suffered the typical rotten riser demise and sucked water into #8 and the original owner decided to go with newer MPI engines vs the TBI. The guy I got them from stored them outside and only covered the openings on it, so it rusted from sitting. It was flushed with freshwater before being pulled though. He ran into hard times and FINALLY parted with them for $700 for the pair. I figured the fuel injection systems were worth more than that alone(the last one I saw on E-bay sold for $900 for 1 system). If you heard this thing run, you would change your mind about it real quick.

Re: Just for HAMMER, my latest project(with pics)
 

Well here's an update on this project. As was pointed out earlier, she was fairly rusty. So here she is in the cleanup process and in paint.

After wire brushing still wet from the first coat of OSPHO.
http://i162.photobucket.com/albums/t...CRUISER001.jpg
http://i162.photobucket.com/albums/t...CRUISER002.jpg
http://i162.photobucket.com/albums/t...CRUISER003.jpg
http://i162.photobucket.com/albums/t...CRUISER004.jpg

After 3 coats of OSPHO to rusted areas, then 2 coats of ZINCROM primer and 3 coats of black engine ENAMEL. Cleaned up pretty nice.
http://i162.photobucket.com/albums/t...CRUISER005.jpg
http://i162.photobucket.com/albums/t...CRUISER006.jpg
http://i162.photobucket.com/albums/t...CRUISER008.jpg
Hopefully the rest of my parts will be in by the end of the week so I can start rebuilding the gimble over the weekend.

Re: Just for HAMMER, my latest project(with pics)
 

Gret Job Therm. You do all the work yourself ??
Didnt you pick up a V recently ?

Re: Just for HAMMER, my latest project(with pics)
 

Unfortunately I'm doing all the work myself, my back and such aint takin to well to it. I got my V several months back, but it turned into a nightmare. So it got put on the back burner. My other project at the moment I forgot to take pictures of before I started, but I'm repairing the windshield frame in my 95 diesel SUB. It got the ever to common rust due to paint peeling(gotta love GM paint). It was repainted before I bought it, but they didn't do the best of jobs and the paint peeled up underneath the urethane that holds the windshield in. So it rusted underneath and leaked like a sprinkler.

Re: Just for HAMMER, my latest project(with pics)
 

Forgot to take pictures. You Slacker. >:(

LOL.... ;D ;D ;D ;D ;D

Re: Just for HAMMER, my latest project(with pics)
 

LOOKING GOOD MAN ;)

Re: Just for HAMMER, my latest project(with pics)
 

Mr. UPS man came today about 4:30, so ig to some more done to it tonight. Maybe I can have her ready in 2 weeks(got some MERCRUISER parts I'm waiting on still).
http://i162.photobucket.com/albums/t...CRUISER011.jpg
http://i162.photobucket.com/albums/t...CRUISER010.jpg

Re: Just for HAMMER, my latest project(with pics)
 

Sounds like the tax man has been nice to ya this year Therm. Motor is looking good. ;)

Re: Just for HAMMER, my latest project(with pics)
 

The tax man aint ever nice to me. I'm trying to get this thing done so I can sell it. ;D

Re: Just for HAMMER, my latest project(with pics)
 

Looks like a lot of hard work but done very well. Keep up the good work.