WTB V20 Steplift
 

What a great board/community. After being told I should drop 15-20K on a used GW or Parker, I discovered the V20. I am located in DC area, but will keep the boat at a slip in Oxford, MD. Getting our new place there has tapped me out for cash, so my budget is small, but it sure seems like I get a lot for money with an older V20.

I am looking for a V20 Steplift with seating for several - we may fish a little, but with my 2 and 1 year old and visitors, we are really looking for a fun cruising/fishing/exploring boat that is reliable and safe.

Basically I am looking for this

http://www.wellcraftv20.com/gallery/...umName=album06

Let me know - winstonbike - at - hotmail.com

Re: WTB V20 Steplift
 

1983 Wellcraft V20 Cuddy cabin
Volvo-Penta 270 outdrive Rebuilt marine engine installed May 2004, 305 CID motor (GM small block ) with less than 10 hours on the motor. New Volvo exhaust manifolds, new osco risers. New thermostat. HEI ignition, 4bbl carb.New Volvo Shift/throttle control. New trim hoses for outdrive. New teleflex gauges (except it has the original volvo trim gauge) new LED marine toggle switches and new fuse holders in dash. Most of the boat has been re-wired using upgraded tinned copper marine wire, tinned connectors, crimped, soldered and heat shrink tubing used on all upgraded wiring. New fuse box behind the console. New VHF Radio and antennea. New AM/FM/Cass stereo w/2 speakers. I added cockpit lights, and 2 power outlets at the helm. Dual battery system with new battery switch. Battery hatches replaced with new plastice hatches. Rod holders and most deck hardware upgraded to stainless steel. Bimini top. Just put the first coat of deckpaint on this weekend. All the old screw holes were filled. New deck plates in the hatch above the fuel tank when the core of that hatch was replaced. New rubrail. I had a section of the stringers replaced at a yacht repair shop when I lived in Virginia. Where the motor mounts bolt into the stringers had some water intrusion, the didn't use bedding compound and sealer when the motor was originally installed. I have trimmed down the bow rail about 6 inches, it always seemed to be right in my line of sight. I have dones tons of other stuff on the boat also, just too much to list. I was doing a little maintenance and repair and like always, I got carried away.

Re: WTB V20 Steplift
 

Message Blue_Runner he has a older V20 with a new transom I think he want's to sell.

Re: WTB V20 Steplift
 

Thank you Skool, indeed I do. Only problem is, I'm off for vacation next week and won't be taking pictures until I get back! There are a few pictures in my gallery but they are liable to scare you off - done ALOT of work since those pics were snapped. If you ain't bought Franco's boat by then, stop in a take a look :)

I'm gonna be clearing house when I get back. I have 3 boats to sell (2 with motors) and 2 separate small motors 5hp and 1.5hp and the 150 Yamaha that's posted on this board (butterfly not included ;)).

Re: WTB V20 Steplift
 

Hey Blue why don't ya put that extra 150 yama on the old V20? Make a package deal out of it. Hey check out the Anchor Issues under General lol. See ya BR

Re: WTB V20 Steplift
 

IMHO that '72 needs a 20" motor. I do have a fixed mount jackplate, but I would not be doing that transom a favor by putting that jackplate back on it. If somebody wants to buy both, well they can have at it and do that if they so desire. The transom is strong now, but I just wouldn't take any chances.

Selling separately should allow more flexibility for the buyer(s) too, i.e. somebody that just needs a motor, or somebody that already has a motor and needs a hull, etc. Again, just my opinion though.

Re: WTB V20 Steplift
 

have a v20 for sale
boat, motor, trailer, 6K
email me for pics and info

Re: WTB V20 Steplift
 

TTT

Re: WTB V20 Steplift
 

Winsot, I don't know if you're still looking, but if you find a V-20 with the fittings in the deck for the full stern bench, I have a bench in good condition in my shed that I'm not going to use any more. It can easily seat three adults or some mixture of kiddos and adults. Fits best in a hull with a bracket.

Re: WTB V20 Steplift
 

CT - I might be interested if fittings can be obtained and the price is right. Got pix? How much?

Re: WTB V20 Steplift
 

BR, you can have it for free. The problem for you will be getting it. I don't know that you'd want to ship it (or that I'd want to ship it to you). It's big, heavy and it doesn't fold *;D. The bench has the original vinyl on it, which is gray. It's solid. The only item that prevents it from being in "very good" shape is one of the buttons on the back is dangling by it's thread. I thought I'd use it all the time, but I've bought the folding marine deck chairs and I keep those in the cabin when I'm fishing and pull them out when I'm entertaining.

But if you happen to be driving through CT in either a pickup or a mini-van I'm happy to see it go to someone who will use it. If you really want it we can work something out on getting my lazy butt over to the UPS depot so long as you handle all the legwork. My zip is 06880.

Re: WTB V20 Steplift
 

So BR, I was just looking in your gallery and if the bench would be for the V-21, then you should know that it would block your access to the port and stern hatches you have in your transom. I'm not sure what's in the deck at the stern of your boat but the bench covered the back half of my round livewell back there, although it still opened. The bench is held in with pins that go into female fittings mounted flush in the deck and can be pulled fairly easily to move it, but my deck still shows the grooves that were created by the previous owner doing this to access a hatch in my transom that was blocked by the bench.