Re: Skool's V20 Rebuild starts
 

sorry guys only worked on the boat today for about 3 1/2 hours but here's what got done.

Holes that i had ground i filled with glass and resin

http://i8.photobucket.com/albums/a46...MVC-001S-3.jpg]

http://i8.photobucket.com/albums/a46...MVC-003S-5.jpg

http://i8.photobucket.com/albums/a46...MVC-005S-4.jpg

http://i8.photobucket.com/albums/a46...MVC-006S-3.jpg

http://i8.photobucket.com/albums/a46...MVC-008S-4.jpg

http://i8.photobucket.com/albums/a46...MVC-010S-4.jpg

http://i8.photobucket.com/albums/a46...MVC-011S-4.jpg

Here's the old transom light hole and the 2 side rod holes someone cut out in bad locations, i filled with plugs of wood i made fit tightly in the holes

http://i8.photobucket.com/albums/a46...MVC-002S-5.jpg

http://i8.photobucket.com/albums/a46...MVC-004S-5.jpg

http://i8.photobucket.com/albums/a46...MVC-012S-3.jpg

Here are those holes above after i glassed over them and filled with resin in the voids

http://i8.photobucket.com/albums/a46...MVC-013S-3.jpg

http://i8.photobucket.com/albums/a46...MVC-014S-3.jpg

http://i8.photobucket.com/albums/a46...MVC-017S-4.jpg

This is a cracking issue that i had in a corner but it was actually only in the gel coat but i glassed and filled anyway

http://i8.photobucket.com/albums/a46...MVC-016S-3.jpg

http://i8.photobucket.com/albums/a46...MVC-015S-3.jpg

notice the top of the transom i epoxy coated with filler to make smooth before i glass over the transom with a layer of glass.

http://i8.photobucket.com/albums/a46...MVC-007S-4.jpg

Re: Skool's V20 Rebuild starts
 

Great Job SKOOL. :D
Did you raise that transom ?

Re: Skool's V20 Rebuild starts
 

yeah rebuilt to 25" transom

Re: Skool's V20 Rebuild starts
 

well i came in from V repairs and look who was sleeping

Sylvester

http://i8.photobucket.com/albums/a46...s/MVC-018S.jpg

Look at Taz his twin brother sleeping in the window

http://i8.photobucket.com/albums/a46...s/MVC-019S.jpg

Re: Skool's V20 Rebuild starts
 

Skool, what ya think of that product called Seacast ?.

Re: Skool's V20 Rebuild starts
 

I test drove a V-20 center console with a 94 140 on it(large gearcase, finger port motor I believe). It had plenty of get up and go I thought, felt like a good match. You can always tweak that 140 a little if needs be to ;D.

Re: Skool's V20 Rebuild starts
 

i say don't use Hammer


Thanks Ferm i wondered if anyone had been on one with a 140 but the CC is lighter than the cuddy

Re: Skool's V20 Rebuild starts
 

I know a 140 is the way I am going on my V-20 CUDDY(when I finally can get to it). It currently has an 83 1.6L SEA-DRIVE on it(115 powerhead rated) and it will get on plane without issue, but top end is a bit lacking. If you consider though my sea-drive is around 100HP propshaft, a 140HP propshaft rated engine would do nicely.

Re: Skool's V20 Rebuild starts
 

i had a 140 looper on my cuddy at one time it would cruise about 26 top end 34 mph

Re: Skool's V20 Rebuild starts
 

i ground all the glass repairs so far and then filled with resin and micro ballons for filler

http://i8.photobucket.com/albums/a46...MVC-001S-4.jpg

http://i8.photobucket.com/albums/a46...MVC-002S-6.jpg

http://i8.photobucket.com/albums/a46...MVC-003S-6.jpg

http://i8.photobucket.com/albums/a46...MVC-004S-6.jpg

http://i8.photobucket.com/albums/a46...MVC-005S-5.jpg

http://i8.photobucket.com/albums/a46...MVC-006S-4.jpg

http://i8.photobucket.com/albums/a46...MVC-007S-5.jpg

http://i8.photobucket.com/albums/a46...MVC-008S-5.jpg