Wellcraft V20 Community

Wellcraft V20 Community (https://forums.wmpdevserver1.com/community/index.php)
-   General (https://forums.wmpdevserver1.com/community/forumdisplay.php?f=10)
-   -   Well it's official!! (https://forums.wmpdevserver1.com/community/showthread.php?t=3118)

Pipe_Dream 04-16-2007 12:04 PM

Re: Well it's official!!
 
Quote:

Originally Posted by reelapeelin



That's a nice 21...but I surprised you'd swap PD for it *:o ...

Nah, just kidding. Shhhhhhhhhhh! Don't want the old gal to hear this kind of talk!

willy 04-16-2007 12:04 PM

Re: Well it's official!!
 
Yea Dawg is a state of mind ;)

Gator good job man, I cannot imagine that year lift kept boat would have any real problem with a soft spot unless you are talking about one of the hatch covers, tank covers etc. You did good, I saw that one a few days after I put my down payment on my G3 and it bothered me for days, agonized over the reasons I sold my V and second guessed my self over and over. In the end it worked out, I did the right thing and a good guy got the Lake Norman V21
Congrats ;)

Blue_Runner 04-16-2007 12:11 PM

Re: Well it's official!!
 
Yeah, where is this "soft spot"??

Love that mooring cover. If you want to sell it I know someone interested ;D

Gator_Bait 04-16-2007 12:44 PM

Re: Well it's official!!
 
Quote:

Originally Posted by C YENSEN

I would probably say that is a safe bet.... ;)


That is a safe bet! ;D 8)

I love to fish. I am fairly new up here to the seasonal fishing and stripers, looking forward to it though! I am from Florida so used to fish offshore mostly. Can't wait to get her out on the bay!

As for the soft spot, it's sort of in the middle of the rear area just in front of and under the bench seat in the rear. I suspect perhaps water could have gotten in either that rear deck plate or the recessed brackets which you screw that bench seat into. I think I will remove both and use maybe 4200 or 5200 on both of them just to prevent further intrusion.

I also need to seal up around the drain tubes in the motor well. I think some moisture may have entered there due to a gap in where the brass tube exits the transom. I removed the scuppers to replace them and some water seeped out of the bottom hole, but it seems dry now. So I'm letting it dry good this week and will epoxy that up this weekend and put on the new scuppers. The transom is solid as a rock, I can jump on the motor and get no flex, so hopefully it's just aorund those tubes. I guess I'll know more when I start drilling to mount a transducer. I figure the more I can do to prevent it now before using the better in the long run.

Thanks everyone and yes Blue should still be top dawg ;D ;D

fireattackvdf335 04-16-2007 12:52 PM

Re: Well it's official!!
 
Great Job Gator!!!! Sweet V! May you have many years of enjoyment with her!!!!! :D

Gator_Bait 04-16-2007 12:54 PM

Re: Well it's official!!
 
Quote:

Originally Posted by Blue_Runner
Yeah, where is this "soft spot"??

Love that mooring cover. * If you want to sell it I know someone interested *;D


I will. I am keeping it in dry dock right now so that cover isn't even going to be on it most of the time I don't think. I may use it, but not sure just yet if it's necessary inside the boatel.

It's new he had it made a few months ago I think.

Blue_Runner 04-16-2007 12:59 PM

Re: Well it's official!!
 
Quote:

Thanks everyone and yes Blue should still be top dawg
Too funny Gator!

Nah, we can share the top dawg title....I'm just glad to have someone to relate to around here ya know ::)

Stinky_Hooker 04-16-2007 01:02 PM

Re: Well it's official!!
 
Well done!! Sweet V!!!

macojoe 04-16-2007 07:33 PM

Re: Well it's official!!
 
Congrats!!

Of coarse I have know about this for a while ;)

It was tuff not saying anything!! And then there was another member that wanted it also, that pm'ed me!!
I was stuck and said well there is someone else from the board looking right now, and I think he is getting it.

Ya did a great job there Gator!

frayed_knot 04-16-2007 07:33 PM

Re: Well it's official!!
 
Very nice boatie. Congrats and welcome to the fold Brother.


All times are GMT -5. The time now is 12:48 AM.

Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.