Re: 21 Project Part 2 The Finish is Coming
 

well boyz sorry no pics yet to tired but i worked on my wiring this afternoon. tested the motor circuit, lighting, and bilge pump. i came home and the mail man had left me gifts my wiring plugs were in from Jameco.com in Calf. Unlike Mj i'm doing pro job and neat on this wiring.

Re: 21 Project Part 2 The Finish is Coming
 

well more wiring done tonight and worked on the Evinrude 225 i picked up over Easter.

Re: 21 Project Part 2 The Finish is Coming
 

What no pics of the Rudey being taken apart. ;D
You ship me out my seats yet. ;D

Re: 21 Project Part 2 The Finish is Coming
 

what you mean like MJ :'( every one is picking on me :'(

Re: 21 Project Part 2 The Finish is Coming
 

It's ok MJ your wiring is ok if you like spaghetti ;D Well did more work today and have pics will post later tonight

Re: 21 Project Part 2 The Finish is Coming
 

Well today after all wiring and other stuff i decided to install a new lanyard in the boat since it had never had one i thought it would be a nice addition. Here's the dash after all mounted.

http://i8.photobucket.com/albums/a46...MVC-008S-2.jpg

http://i8.photobucket.com/albums/a46...MVC-009S-2.jpg

Here's the back of the ign. switch and control panel. The white net has the warning horn inside it.

http://i8.photobucket.com/albums/a46...MVC-010S-2.jpg

http://i8.photobucket.com/albums/a46...MVC-013S-1.jpg

http://i8.photobucket.com/albums/a46...MVC-016S-2.jpg

Here's the plugs i ordered from Jameco.com one is to connect the motor harness and the other is for the boat harness to the fuse panel.

http://i8.photobucket.com/albums/a46...MVC-015S-2.jpg

http://i8.photobucket.com/albums/a46...MVC-014S-2.jpg

Here's the fuse panel wired

http://i8.photobucket.com/albums/a46...MVC-011S-1.jpg

Here's the 2 lower gauges fuel and voltage.

http://i8.photobucket.com/albums/a46...MVC-012S-2.jpg

Re: 21 Project Part 2 The Finish is Coming
 

nice work skools. That is one area where I do NOT excel, wiring and wiring diagnosis.....yuk.....why is the warning alarm wrapped in that mesh stuff?

Re: 21 Project Part 2 The Finish is Coming
 

wrapped up to protect the main wiring harness from it's weight in one spot and to keep out direct water spray.

THanks i hope it looks good to you guys i strapped up all the wiring with c clips for low voltage wiring, i know the pics are hard to know where it's looking but i was under the dash taking the pics.

Re: 21 Project Part 2 The Finish is Coming
 

Glad to see ya back at work with her. Looking good there SKOOL. ;D

Re: 21 Project Part 2 The Finish is Coming
 

pictures for Hammer lol this is the 1990 motor i picked up over Easter. What ya think i only gave $50 for it, 225 Evinrude 25" shaft.

http://i8.photobucket.com/albums/a46...MVC-001S-2.jpg

http://i8.photobucket.com/albums/a46...MVC-002S-2.jpg

http://i8.photobucket.com/albums/a46...MVC-003S-2.jpg

http://i8.photobucket.com/albums/a46...MVC-004S-2.jpg

http://i8.photobucket.com/albums/a46...MVC-005S-2.jpg

http://i8.photobucket.com/albums/a46...MVC-006S-1.jpg

Took off the heads to look at the salt and to my shock very little, the compression is 90 psi on all but 1 it has 80 so i took the head on this side first and found cylinder has some scoring, i'm going to re-ring her any way then. The marina said it was scrap and they had sold the power pack off due to bad flywheel, all it needed was magnets re-glued, dummies lol.

http://i8.photobucket.com/albums/a46...MVC-007S-1.jpg