Log in

View Full Version : Trim & Tilt leak

macojoe
10-08-2007, 10:43 PM
Ok as many know I took the boat out today (See General section) and the center Oring is leaking on the ram *:'(

Now I am not looking forward to hammering out that big rusted pin, and then having to get the knuckle off, so That I can slde the cap off for a seal.

Now would something like Lucas stop leak work??

Tired of working want to be fishing!
THEFERMANATOR
10-08-2007, 10:57 PM
MJ you've gone this far to make it right, don't half A$$ it now. Go ahead and fix her right and be done with it. Lucas is a band aide at best, it's also thicker than gear oil. Most all of your stop leaks use brake fluid to stop the leaks. They work by swelling the rubber, but it is a temporary fix as the swollen rubber will eventually tear and make the leak worse.
macojoe
10-09-2007, 04:15 AM
I guess you are right, I hate to admitt it!

So let me ask you, see if I get this right.

1 block the motor up

2 Knock the pin out

3 twist the knuckle off (whats the beast way to hgold the shaft??)

4 unscrew the cap and take off, replaxce center seal (leaking) and add new O ring on ther cap, reassamble.

5 top off fluid and ck for leaks.

Does that about cover it??

Thanks!
macojoe
10-09-2007, 12:51 PM
Ok the pin is so rusted that I have no idea which way in comes out??
I have playedm a bit with it and it isn't going to move with out a fight!!

But which way??
Skools Out
10-09-2007, 08:49 PM
you mean the top pin or the bottom? top will go either way just like CB lol
macojoe
10-10-2007, 01:03 AM
LMFAO!!

Thanks its the top one!! I tryed for 1/2 hour today and it is not moving!

I added Fluid and it works for now! Can yiou use heat??
Skools Out
10-10-2007, 01:27 AM
yeah heat and lots of Kroil but use a large hammer knock it both directions till it's loose. the pin should have been stainless. just don't mushroom it to where it won't come out.
Kajun
10-10-2007, 01:47 AM
just checking but did you take the snap rings off it yet?
Skools Out
10-10-2007, 01:51 AM
lmao
macojoe
10-10-2007, 03:25 AM
No snap rings, had wire thur a hole on each end. ;D
macojoe
10-10-2007, 03:26 AM
If I have to I will drill a hole thur and then insert a hack saw blade and cut, then hammer it out.
chumbucket
10-10-2007, 04:00 AM
you mean the top pin or the bottom? top will go either way just like CB lol
Whaaaaaa???????? >:(
Skools Out
10-13-2007, 12:14 AM
here's a pin i had removed awhile back if you want to see one with it's clips removed

http://i8.photobucket.com/albums/a46/Skools_Out/Motors/MVC-005S-4.jpg

here's the hole it belongs in lol

http://i8.photobucket.com/albums/a46/Skools_Out/Motors/MVC-006S-3.jpg

http://i8.photobucket.com/albums/a46/Skools_Out/Motors/MVC-007S-4.jpg

http://i8.photobucket.com/albums/a46/Skools_Out/Motors/MVC-008S-2.jpg
coork
10-13-2007, 06:02 PM
I used air hammer to get mine out.........