New Cables and Controls

[macojoe]

I hate installing them!! I had big problems when I did mine and now I am having big problems doing this new motor!! >:(
You would think they would be so simple to do? Just two cables and 4 conections? but I have the biggest time every time I do a set of them >:(

[chumbucket]

Get them snaked in yet? I know the last time we talked you said that the tube was full with all the current wiring and all. I was wondering about the possibilty of getting a smaller flexible tube with the new stuff running through it in there. Not inside the tube that's already there, but on top of or beside it.
??? ??? ??? ??? ??? ???

[macojoe]

All installed!! But I am having a problem with the control box?? I hook the cables up to the boy and not the motor and I can not get a full throw in forward gear?? But i do in reverse?? It should be the other way around??
I am co confused?? I have tryed everything!! I called the marina that I bought all the stuff from and they have no idea eaither?? I did everything they said to do and I have read the Inctrion and did as it says and still all messed up!!
And yes they sre the right cables!! It is on tyhe control box end as I have not even hooked the to the motor yet??
I need help!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Please anyone!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

[chumbucket]

Binnacle mount? If so, I've had the same problem in the past. Try putting some washers to act as spacers between the control and the console. It may be hitting underneath and preventing a full throw. Start by raising it 1/4"-3/8" and see if it works. Or, try raising (spacing) under just the front or rear of the controller. This worked for me before, then afterwards, I made a solid spacer to go under the controls. Actually, I think Yamaha makes a spacer just for this purpose. I know you're not installing a Yammi, but give it a try.
I'm sure you're ready to try anything right now just to get the f'ing thing done and out of the yard.

[macojoe]

I have it all set!! I guess I had it in the wrong hole?? the hole os about 1/4 " or less from the other . But all set now!!
I should have it out of here oo Sunday!! ;D ;D ;D ;D ;D

Now I can get mine uncovered!!
I hope to sell that motor soon so I can go get te trailer! But I have alot to do before needing it here anyway, maybe next week??

[chumbucket]

;D

[macojoe]

The boat is done!!! I have completely repowered my buddys 1992 Henry O'
Everything is new!! I mean the motor, wire harness, cables, gas line, steering system, control box, tac, tilt & Trim gauge, hour meter. Everthing even bottom paint!!

Now I can start my boat!

http://img43.photobucket.com/albums/v131/macojoe/m49.jpg

[Mac_Attack]

Nice job MJ! *If I need help replacing the Force some day, do you *travel? *Other than to Calif! *Mac Attack ;D

[macojoe]

I hate center consols!! as far as repowering them!!! Everything has to under the floor in them and what a Bit$h!! I would not what to do another to soon!!

But for the right price I will travel any where!! ;D

I just put all new shocks on my buddys 4 Runner and he picked up the baot.

Thats my boat covered in the back ground! I pulled the cover today and looked in side and said not today!!!
I was tired. Maybe this week ?? I hear that it is going to rain most of the week?? Figures, I want to do something for me now! :-/

[chumbucket]

He must be as happy to get it back as you are to get it out of the yard. Should run pretty nice with that new Johnson. I always liked the unique styling of them Henry O's. 17' is just a tad on the small side though. But with a bow like that and with the chines, should be a relatively dry boat. 8)

[macojoe]

Not only is it a dry boat, but it is one of the best riding boat I have been in!
This thing takes the water like a dream!! But is small. We went out toghter one day and it is a small boat for two big guys!
But they make it in a 21 to!! ;D